KTG Fasteners

Strength of this fastener is derived from the compression of the plates, mounted above and below the belt, with high tensile strength bolts. this "compression" distributes the splice tension across the full width of each fastener plate. The holding ability is, thereby, increased by not solely relying upon the bolts to resist pull-out.

Additional strength and resistance to pull-out is obtained from the specially formed teeth on each plate. These teeth imbed deep into the belt carcass, but without damaging the carcass fibers.

A tight butt splice is achieved through the exaggerated bolt hole spacing in the templet which forces the belt ends together. And, the Bolt Solid Plate Fasteners permit natural conformance with troughing or transition idlers.

Product Description:

Steel Belt Lacing has continuous claws, no risk to contaminated the carried product.It is easy to install with hammer tool.
 

Technical data

  1 140 190 2 2 1/2
Belt thickness, mm 5 - 11 5 - 11 8 - 14 11 - 17 14-21 19-25
Mini pulley Ø, mm 250 300 400 400 700 1 000

 

  • Continuous claws : cannot contaminate the carried product
  • Easy and simple to install with the hammer tool
  • Low flush finish on belt
  • Perfect for transmission belt (leather/cotton/PVC-PU)


Steel quality / Galvanized steel or stainless steel

Installation method / Hammer tool

 

Fastener Metals

 

Options

Bolt Solid Plate fasteners come in a variety of metals for many applications.

Steel

For most applications, the standard fastener material, carbon steel, is suitable. Available in all sizes.

Stainless Steel

Type 316 is non-rusting and provides extra resistance to abrasion, magnetic attraction and corrosion from acids and chemicals. Available in all sizes except No. 2 ½ and 3. Furnished as Stainless Top Plates with the balance steel or as all stainless, including bolts and nuts.

Everdur

Spark-free material compared to steel and fully non-magnetic. Alloy of copper and silicon for use in grain elevators and other potentially explosive environments, or on belts with magnetic pulleys or separators. The word Everdur is a trademark of American Brass.

Megalloy

For superior resistance to wear and abrasion, Megalloy is available in sizes 140, 190, 1 ½, 2, 2 ¼ and SP6. Provides several times the service life of regular steel. Not recommended where corrosion is a problem. Megalloy is a trademark of Flexible Steel Lacing Company.

Monel

Where abrasion, rust or corrosive acids quickly deteriorate steel, this nickel/copper alloy is effective. It is available in sizes 1, 1 ½, 2, 2 ½ and 3 only, and furnished as Monel Top Plates, balance steel or all Monel, including bolts and nuts. The word Monel is a trademark of Huntington Alloys, Inc.

Promal

For severe abrasion resistance in corrosive environments such as coke and sinter operations, use Promal Top Plates. These are heat treated, malleable castings. Promal Top Plates (available in Nos. 140, 190 and 1 ½) furnished with steel bolts, nuts and bottom plates. The word Promal is a trademark of FMC Corporation.

Rubber-Covered Steel

To maintain a smooth surface when splice has been countersunk with the JV tool and router method, use Rubber-Covered Top Plates. They fill the space above the top plate with a 1/8" thick rubber cover for a continuous, smooth belt surface.

 

 


KOYO Bearings

A bearing is a machine element that constrains relative motion to only the desired motion, and reduces friction between moving parts.

Mitsuboshi Belts

A belt is a loop of flexible material used to link two or more rotating shafts mechanically, most often parallel.

Oil-Seals

A Seal is a device that helps join systems or mechanisms together by preventing leakage.

Roller-Chain

is a way of transmitting mechanical power from one place to another.

Danzol Grease & Lubricants

Lubrication is simply the use of a material to improve the smoothness if movement of one surface over another

Sprockets

is a profiled wheel with teeth, cogs, or even sprockets that mesh with a chain, track or other perforated or indented material.

KSM Bearing-Units

A pillow block is a pedestal used to provide support for a rotating shaft with the help of compatible bearings & various accessories.

Fasteners

Strength of this fastener is derived from the compression of the plates, mounted above and below the belt, with high tensile strength bolts.